JobStep Safety
  • Sourced from OSHA regulations and guidance
  • Updated October 2026
  • Every quote checked word for word

Read this to your crew

1. Not every fall is from a roof

When we talk about falls, people picture an edge. But plenty of injuries happen at ground level: a foot on a wet ramp, a boot catching a cord, a step down into a hole nobody covered. OSHA counts falls among the most common causes of serious work-related injuries and deaths, and it includes the floor in that:

“Keep floors in work areas in a clean and, so far as possible, a dry condition.”

A fall on the same level can still mean a broken wrist, a torn shoulder or a head hitting concrete. And on a site, the ground floor is often not the lowest level.

2. Slips: watch the surface

You slip when your foot loses grip. On a job that is usually water, mud, ice, oil, form release, or dust on a smooth slab. After rain or a freeze, entrances, ramps, decks and steel are the worst. OSHA's winter advice is to clear snow and ice and spread deicer as soon as possible after a storm, and when you have to cross ice, to wear boots with good treads and walk slowly with short steps so you can react when the grip changes. [OSHA] If something gets spilled, it gets cleaned up now, by whoever spilled it.

3. Trips: look at the path

You trip when your foot hits something and the rest of you keeps going. The usual culprits on a site are scrap lumber, offcuts and packaging, so the rule is that debris is kept out of work areas, passageways and stairs, and form and scrap lumber with protruding nails is named in it. [OSHA] Cords and hoses are the next: walkways are kept clear of cords. [OSHA] Then holes: every hole someone could trip in or step into gets a cover, however short the drop. [OSHA]

4. See where you are walking

You cannot avoid what you cannot see. If a load blocks your view of your feet, it also blocks your view of the cord and the offcut, so plan the carry before you pick it up. And do not walk where it is dark: work areas and access routes have to be lit while work is going on, at least 5 foot-candles indoors in corridors, hallways and exitways. [OSHA] If a stairwell is dark, the light gets fixed before the stairs get used.

5. Fix it or flag it

If you see a hazard on a walkway, deal with it now if it takes a minute: pick up the offcut, move the cord, close the cover. If it takes longer, block it off and tell the supervisor. The general industry rule says the same thing in plain terms: a hazard on a walking surface is fixed before anyone uses it again, or guarded until it is. [OSHA]

The walkaround check

Walk the routes the crew will use today, from the parking area to the work, and look for these:

Look forWhat to do
Scrap lumber, offcuts, banding or packaging in a walkway or on stairsCleared from work areas, passageways and stairs as you go, into the bins provided. [OSHA]
Boards with nails sticking upMoved off the walking path. Scrap lumber with protruding nails is named in the rule. [OSHA]
Cords and hoses across the pathMoved out of the walkway. Walkways are kept clear of cords. [OSHA]
An open hole, sleeve or floor openingCovered, secured and marked, so nobody trips or steps into it. [OSHA]
Ice, snow, mud or standing water at entrances, ramps and decksCleared, with deicer spread, as soon as possible after a storm. [OSHA]
Oil, grease or a leak on the floorCleaned up, and the leak fixed. General industry's rule names spills and leaks as hazards to keep off walking surfaces. [OSHA]
A dark stairwell, corridor or access routeTemporary lights up to at least the table minimum before work goes on there. [OSHA]

Stairs on a job site

Temporary and half-built stairs are where slips, trips and falls meet. The construction stair rule covers the common problems:

  • Slippery conditions on stairs are fixed before the stairs are used to reach other levels. [OSHA]
  • Every part of the stairway is free of hazardous projections such as protruding nails. [OSHA]
  • Risers and treads are uniform in each flight, with no more than a quarter inch of variation in the stairway system. Uneven steps are what catch a foot. [OSHA]
  • Once a stairway has 4 risers, or climbs over 30 inches, whichever comes first, it gets at least one handrail. [OSHA]
  • Pan stairs waiting for concrete are not walked on unless the pans are temporarily filled with wood or other solid material to the top edge. Skeleton metal stairs waiting for treads are not walked on unless secured temporary treads and landings are fitted. [OSHA]

Questions for the crew

  1. On your way in this morning, what did you step over or around? Is it still there?
  2. Where on this job does water, mud or ice collect, and who deals with it first thing?
  3. Which cords or hoses cross a walkway right now, and where can they go instead?
  4. Which stairs or access routes are poorly lit, especially early and late in the day?

A sign-in sheet prints after this talk. For a blank copy to use at other meetings, the free sign-in sheet template comes as a PDF or Word file.

What the law says

There is no single slips and trips standard in construction. The rules are spread across several sections. The housekeeping rule is the one most crews break:

“During the course of construction, alteration, or repairs, form and scrap lumber with protruding nails, and all other debris, shall be kept cleared from work areas, passageways, and stairs, in and around buildings or other structures.”

The others: cords out of walkways in 1926.416, hole covers in 1926.501, stairways in 1926.1052 and lighting in 1926.56. Workplaces under general industry rules, such as shops and yards, follow 1910.22, which requires walking surfaces kept clean, orderly and, as far as feasible, dry, and free of hazards such as loose boards, leaks, spills, snow and ice. [OSHA]

When the route itself is the risk, such as carrying material across an icy deck or working around open floor penetrations, write the steps and controls on a printable JHA template. If you would rather hand it off, a Custom JHA writes one for your crew's actual task with the OSHA rules that apply.

More talks on falls

The 52-Week Toolbox Talk Planner covers slips on ice and snow in week 2, ladders in week 4 and housekeeping in week 5, before the five weeks on falls from height in the spring.

Questions

Common questions

What is the difference between a slip, a trip and a fall?

A slip is when your foot loses grip on the surface, such as on ice, mud, oil or a wet floor. A trip is when your foot hits something and your body keeps going, such as a cord, a board or the edge of a hole. Both end in a fall, either on the same level or down to a lower one. This talk covers falls on the same level and on stairs; falls from height have their own talk.

What does OSHA require to prevent slips and trips in construction?

Several rules work together. Debris and scrap lumber with protruding nails are kept cleared from work areas, passageways and stairs (1926.25). Walkways are kept clear of electrical cords (1926.416). Holes get covers so nobody trips or steps into them (1926.501). Stairs are kept free of slippery conditions and hazardous projections (1926.1052). And work areas are lit to minimum levels (1926.56).

When does a stairway on a construction site need a handrail?

Once it has 4 risers, or climbs over 30 inches, whichever comes first, at least one handrail is required, under 29 CFR 1926.1052. Riser heights and tread depths also have to be uniform within a flight, with no more than a quarter inch of variation in the stairway system.

How much lighting is required on a construction site?

OSHA's table sets minimums in foot-candles while work is going on: 5 for general construction area lighting and for indoor corridors, hallways and exitways, and 3 for general construction areas such as access ways, excavation and waste areas, active storage areas and loading platforms.

Can I print this slips, trips and falls talk as a PDF?

Yes. Use the print button and choose Save as PDF, or print it straight to paper. The talk, the walkaround check, the crew questions and a sign-in sheet print together.

More toolbox talks and meeting help

Also useful

Sources