JobStep Safety

Instant download · PDF and Word

Filled JHA examples: 40 completed job hazard analyses for construction

Every JHA in this library is already written: the steps of the task, the hazards in each step, the controls, the PPE, the training it needs and the OSHA construction rules that apply. Open the one for today's task, fill in your site details, check it against the job and go over it with the crew. New to JHAs? Start with how a job hazard analysis works.

  • 40 tasks in 9 trade groups, 254 steps
  • Every rule with its 29 CFR 1926 section
  • Editable Word files and print-ready PDFs
  • Crew sign-on sheet in every JHA

Filled JHA Example Library

$29$39

Launch price until Dec 31, then $39

One payment, no subscription. Yours to keep and print.

Get the library See all 40 tasks
  • Secure checkout by Stripe
  • Instant download, links also sent by email
  • Not right for you? Refund within 14 days

Also need weekly toolbox talks and the incident forms? Get all three for $49

What is in each JHA

The same parts in every one, in the same order

Job facts to fill in

Company, site, location, today's conditions, state, who prepared it and the date, as lines to fill in on site.

The steps, in work order

Five to seven steps per task, written the way a crew does the work, from setup to cleanup.

Hazards and controls for each step

What can go wrong and the harm it causes, then the controls, sorted from removing the hazard down to protective equipment.

PPE, training and competent person

The protective equipment for the job, and each training or competent person duty from the rules that apply to the task.

The OSHA rules that apply

Each rule with its 29 CFR 1926 section number and a plain-words line. Controls with no rule behind them are written as good practice.

Before-work checklist and sign-on

Highlighted lines to confirm for your site (911 address, hospital, rescue plan where needed) and a crew sign-on sheet.

The task list

All 40 tasks, by trade

Ladders, scaffolds and lifts

  • L01Working from an extension ladder5 steps
  • L02Working from a stepladder5 steps
  • L03Erecting and dismantling a frame scaffold6 steps
  • L04Working from a supported scaffold5 steps
  • L05Working from a boom lift6 steps

Roofing

  • L06Tearing off asphalt shingles on a house roof7 steps
  • L07Installing asphalt shingles with nail guns7 steps
  • L08Replacing a low-slope roof membrane7 steps
  • L09Installing skylights and covering roof openings6 steps
  • L10Torch-applied modified bitumen roofing6 steps

Excavation and sitework

  • L11Trench excavation with a trench box7 steps
  • L12Digging near underground utilities with an excavator7 steps
  • L13Laying pipe in a trench6 steps
  • L14Backfilling and compacting a trench6 steps

Concrete and masonry

  • L15Building and stripping concrete wall forms7 steps
  • L16Placing and tying rebar6 steps
  • L17Pouring concrete with a pump truck6 steps
  • L18Cutting and coring concrete6 steps
  • L19Laying a concrete block wall7 steps
  • L20Fastening with a powder-actuated tool6 steps

Carpentry, drywall and painting

  • L21Framing and raising walls on a house with nail guns6 steps
  • L22Cutting lumber with circular and miter saws6 steps
  • L23Hanging and finishing drywall7 steps
  • L24Installing floor sheathing over open joists on a house7 steps
  • L25Exterior painting from a boom lift7 steps

Electrical

  • L26Replacing an electrical panel6 steps
  • L27Setting up temporary power on a jobsite7 steps
  • L28Electrical rough-in: pulling wire and installing branch circuits6 steps

Welding, cutting and demolition

  • L29Arc welding on a construction site6 steps
  • L30Cutting with an oxy-acetylene torch6 steps
  • L31Grinding and cutting metal with an angle grinder6 steps
  • L32Interior demolition of walls and ceilings7 steps
  • L33Removing debris through a chute from upper floors6 steps

Equipment, cranes and traffic

  • L34Loading and unloading materials with a rough-terrain forklift7 steps
  • L35Making a lift with a mobile crane7 steps
  • L36Rigging, signaling and landing a crane load7 steps
  • L37Operating a skid steer loader7 steps
  • L38Flagging traffic in a road work zone6 steps

Confined spaces and lead

  • L39Entering a permit-required confined space7 steps
  • L40Lead-safe paint removal during renovation6 steps

Task not in the library?

Tell us the job and your crew's steps, and we write the JHA for that task, with the rules picked from your answers. Get a Custom JHA ($29)

A full sample from the library

L11: Trench excavation with a trench box

This is the complete JHA as it comes in the library, shown here as a web page. The download has it as a PDF and an editable Word file. Three of the library JHAs, this one included, are free on our JHA examples page.

JobStep Safety

Job Hazard Analysis

Trench excavation with a trench box

Company
________________________
Site or project
________________________
Location on site
________________________
Conditions today
________________________ (weather, ground, access, other work nearby)
Task
Trench excavation with a trench box
Trade
Excavation
State
________________________
Work type
Construction (29 CFR Part 1926)
Prepared by
________________________
Date of the work
________________________
Library reference
L11, Excavation and sitework

How to use this JHA

  1. This JHA is filled in for the task as it is usually done. Walk the job: cross out what does not apply, and add any step, hazard or control your site needs.
  2. Fill in every highlighted line before work starts. In the Word file you can type them in.
  3. Go through each step with the crew at the start of the shift, on site, before anyone starts work.
  4. Have everyone who does the work sign the crew sign-on sheet. Keep a copy on site.
  5. It follows federal OSHA construction rules (29 CFR Part 1926). In a State Plan state, check your state's rules as well.

Before work starts

Highlighted lines must be filled in or confirmed for your site before anyone starts work.

  • Confirm whether a hospital or clinic can be reached quickly from this site.
  • Person in charge on site: ________________________
  • Address or location to give 911 callers: ________________________
  • Nearest hospital or clinic: ________________________
  • Person on site with valid first-aid training: ________________________
  • Competent person for the excavation: ________________________
  • How and when underground utilities were located: ________________________
  • Cave-in protection to be used, and who selected it: ________________________

Protective equipment for this job

  • Hard hat
  • Safety glasses
  • High-visibility vest
  • Safety-toe work boots
  • Hearing protection near the excavator
  • Work gloves

Training and competent person

  • 29 CFR 1926.651(k)(1)A competent person inspects the excavation before work, as needed during the shift, and after rain or other hazard-increasing events.
  • 29 CFR 1926.21(b)(2)Every worker must be instructed in recognizing and avoiding the unsafe conditions and rules that apply to their work.

Step by step

Step 1. Call in the utility locate and mark out the trench

What can go wrong

  • Digging into a gas, electric, water or communication line (explosion, electrocution, flooding, service outage)

How we control it

Work practices and checks

  • Contact the utility locate service before digging, describe the work, and wait until the marks are in.
  • Mark out the trench line in white, and check the locate marks against the drawings and what you see on site.
  • Look for private lines the locate service does not mark, such as site lighting, irrigation and lines to outbuildings.

Rules: 1926.651(b)(1), 1926.652(a)(1), 1926.651(j)(2), 1926.651(k)(1), 1926.651(b)(2), 1926.651(b)(3), 1926.651(b)(4), 1926.416(a)(2)

Step 2. Set up the site, the spoil area and the equipment path

What can go wrong

  • Spoil or equipment too close to the trench edge (cave-in, or material rolling onto workers)
  • Workers on foot in the excavator swing area (struck or crushed by the machine)
  • Open trench left unguarded (falls into the trench by workers or the public)

How we control it

Guards, barriers and equipment

  • Mark off the excavator swing area and keep workers on foot out of it.
  • Fence or barricade the trench area and post warning signs.

Work practices and checks

  • Plan the spoil pile at least 2 feet back from the edge, on the side away from where the crew works.

Rules: 1926.651(b)(1), 1926.652(a)(1), 1926.651(j)(2), 1926.651(k)(1), 1926.602(a)(9)(ii), 1926.25(a)

Step 3. Dig the trench with the excavator

What can go wrong

  • Bucket strikes a marked line near the estimated location (line damage, explosion or electrocution)
  • Machine near the edge undermines the trench wall (cave-in or machine tipping in)
  • Workers under the bucket or next to trucks being loaded (struck by the load or spillage)
  • Engine and bucket noise (hearing loss)

How we control it

Work practices and checks

  • Near a mark, stop and expose the line by hand or vacuum excavation before digging with the machine.
  • Keep everyone out from under the bucket and away from trucks being loaded.
  • Keep the excavator tracks back from the edge as far as its reach allows.
  • Wear the seat belt, and sound the horn before moving.

Protective equipment

  • Wear hearing protection near the running machine.

Rules: 1926.651(b)(1), 1926.652(a)(1), 1926.651(j)(2), 1926.651(k)(1), 1926.651(b)(2), 1926.651(b)(3), 1926.651(b)(4), 1926.416(a)(2), 1926.602(a)(9)(ii), 1926.602(a)(2)(i), 1926.602(a)(9)(i), 1926.600(a)(3)(i), 1926.651(e), 1926.651(h)(1), 1926.651(g)(1)(i), 1926.651(j)(1), 1926.52(b)

Step 4. Set the trench box

What can go wrong

  • Entering the trench before the box is in (cave-in, burial)
  • Box set on uneven ground or with gaps to the trench wall (box shifts or soil falls in)
  • Box swung or lowered over workers (struck or crushed)

How we control it

Remove the hazard

  • Nobody enters the trench until the box is set. Set it from the top with the excavator.

Work practices and checks

  • Use a box with the maker's tabulated data for this depth, and set it as the data says.
  • Keep everyone clear while the box is lifted and lowered, and use rigging inspected that shift.

Rules: 1926.651(b)(1), 1926.652(a)(1), 1926.651(j)(2), 1926.651(k)(1), 1926.652(g)(1)(iii), 1926.651(e), 1926.651(h)(1), 1926.651(g)(1)(i), 1926.651(j)(1)

Step 5. Place the ladder and inspect the trench before entry

What can go wrong

  • No quick way out (workers trapped by water, a cave-in or a gas leak)
  • Cracks, bulges, seepage or rain since the last check (cave-in)
  • Low oxygen or exhaust gas in a deep trench (unconsciousness or death)

How we control it

Guards, barriers and equipment

  • Place a ladder inside the box so no one travels more than 25 feet to get out, and extend it above the top.

Work practices and checks

  • The competent person inspects the trench and the box before anyone enters, as needed during the shift, and after rain.
  • Where a hazardous atmosphere could be present, test the air before entering a trench deeper than 4 feet.
  • Keep engines and generators away from the trench so exhaust cannot collect in it.

Rules: 1926.651(b)(1), 1926.652(a)(1), 1926.651(j)(2), 1926.651(k)(1), 1926.651(c)(2), 1926.651(e), 1926.651(h)(1), 1926.651(g)(1)(i), 1926.651(j)(1)

Step 6. Work inside the trench

What can go wrong

  • Standing outside the box or at its open ends (cave-in, burial)
  • Water collecting in the bottom (slips, soil failure and drowning risk)
  • Tools or material dropped from the top (head injuries)

How we control it

Work practices and checks

  • Stay inside the box at all times. Enter and leave only by the ladder inside the box.
  • Stop work and get out if water is collecting, until it is pumped down and the competent person has re-inspected.
  • Lower tools and material in a bucket or sling, never throw them in.

Protective equipment

  • Wear a hard hat and safety glasses.

Rules: 1926.651(b)(1), 1926.652(a)(1), 1926.651(j)(2), 1926.651(k)(1), 1926.652(g)(1)(iii), 1926.651(e), 1926.651(h)(1), 1926.651(g)(1)(i), 1926.651(j)(1), 1926.100(a), 1926.102(a)(1)

Step 7. Pull the box and backfill

What can go wrong

  • Workers in the trench while the box is moved (cave-in or struck by the box)
  • Machine backing over a worker on foot (crushing)

How we control it

Work practices and checks

  • Everyone is out of the trench before the box is moved or pulled.
  • Backfill in lifts as the box comes up, and use a spotter when backing.

Rules: 1926.651(b)(1), 1926.652(a)(1), 1926.651(j)(2), 1926.651(k)(1), 1926.652(g)(1)(iii), 1926.602(a)(9)(ii), 1926.602(a)(2)(i), 1926.602(a)(9)(i), 1926.600(a)(3)(i)

Rules that apply to this job

Each rule in plain words. The regulation text itself is at osha.gov under the section number.

  • 29 CFR 1926.651(b)(1) Steps 1, 2, 3, 4, 5, 6, 7Find the estimated location of underground utilities before digging.
  • 29 CFR 1926.652(a)(1) Steps 1, 2, 3, 4, 5, 6, 7Workers in an excavation need a protective system against cave-ins (exceptions: stable rock, or under 5 feet deep with no sign of cave-in found by a competent person).
  • 29 CFR 1926.651(j)(2) Steps 1, 2, 3, 4, 5, 6, 7Keep spoil, materials and equipment at least 2 feet back from the edge, or use retaining devices.
  • 29 CFR 1926.651(k)(1) Steps 1, 2, 3, 4, 5, 6, 7A competent person inspects the excavation before work, as needed during the shift, and after rain or other hazard-increasing events.
  • 29 CFR 1926.651(b)(2) Steps 1, 3Before digging starts, contact the utility companies or owners, tell them about the work and ask them to locate their underground installations.
  • 29 CFR 1926.651(b)(3) Steps 1, 3As digging gets close to the estimated location of an underground installation, find its exact location by safe and acceptable means.
  • 29 CFR 1926.651(b)(4) Steps 1, 3While the excavation is open, protect, support or remove underground installations as needed to keep workers safe.
  • 29 CFR 1926.416(a)(2) Steps 1, 3Where the exact location of underground power lines is unknown, workers using jackhammers, bars or hand tools that could contact a line get insulated protective gloves.
  • 29 CFR 1926.602(a)(9)(ii) Steps 2, 3, 7Earthmoving or compacting equipment with an obstructed rear view may reverse only with a working backup alarm or a signal person.
  • 29 CFR 1926.25(a) Step 2Keep scrap lumber with protruding nails and all debris cleared from work areas, passageways and stairs.
  • 29 CFR 1926.602(a)(2)(i) Steps 3, 7Earthmoving equipment covered by this section has seat belts.
  • 29 CFR 1926.602(a)(9)(i) Steps 3, 7Rollers, compactors, loaders, dozers and similar machines have a horn that can be heard over the noise, sounded as needed when moving either way.
  • 29 CFR 1926.600(a)(3)(i) Steps 3, 7Block or crib raised machinery before anyone works under or between it. Fully lower or block blades, buckets and dump bodies when not in use or under repair.
  • 29 CFR 1926.651(e) Steps 3, 4, 5, 6Nobody stands under loads handled by lifting or digging equipment, and workers stand away from vehicles being loaded or unloaded.
  • 29 CFR 1926.651(h)(1) Steps 3, 4, 5, 6Nobody works in an excavation with standing or rising water unless adequate precautions protect them from it.
  • 29 CFR 1926.651(g)(1)(i) Steps 3, 4, 5, 6Where low oxygen or a hazardous atmosphere exists or could reasonably be expected, test the air before anyone enters an excavation deeper than 4 feet.
  • 29 CFR 1926.651(j)(1) Steps 3, 4, 5, 6Protect workers from loose rock or soil that could fall or roll from an excavation face.
  • 29 CFR 1926.52(b) Step 3Above the Table D-2 noise levels, use feasible engineering or administrative controls first, then hearing protection.
  • 29 CFR 1926.652(g)(1)(iii) Steps 4, 6, 7Protect workers from cave-ins while they enter or leave the area inside a shield (trench box).
  • 29 CFR 1926.651(c)(2) Step 5Trenches 4 feet or deeper need a ladder, ramp or other way out within 25 feet of lateral travel.
  • 29 CFR 1926.100(a) Step 6Wear a hard hat where there is a possible danger of head injury from impact, falling or flying objects, or electrical shock and burns.
  • 29 CFR 1926.102(a)(1) Step 6Use eye or face protection against flying particles, molten metal, chemicals, gases or vapors, or harmful light.
  • 29 CFR 1926.21(b)(2) Whole jobEvery worker must be instructed in recognizing and avoiding the unsafe conditions and rules that apply to their work.
  • 29 CFR 1926.28(a) Whole jobThe employer must require appropriate PPE wherever workers are exposed to hazardous conditions.
  • 29 CFR 1926.50(c) Whole jobIf no clinic or hospital is reasonably accessible, a person with valid first-aid training must be available on site.

Crew sign-on

The last page has a sign-on table: name, signature and date for each crew member who reviewed the JHA.

Questions

Common questions, short answers

Something not covered here? Email help@jobstepsafety.com and we will answer.

Ready when you are

$29, one payment. Launch price until Dec 31, then $39.

Get the library
  • Instant download after checkout
  • Refund within 14 days
  • Secure checkout by Stripe
What is a filled JHA example?

A job hazard analysis that is already written for a task: the steps, the hazards in each step, the controls, the PPE and the rules. You check it against your job, fill in the site lines, add anything your site needs, and review it with the crew. A blank template gives you the columns; a filled example gives you the content.

How is this different from the free JHA examples page?

Our free JHA examples page walks through the two worked examples OSHA itself publishes, in OSHA's words, plus three of the library JHAs as free downloads. The library is all 40 construction tasks as finished, editable Word and PDF files.

How is it different from a Custom JHA?

The library covers common tasks the way they are usually done, ready to download now. A Custom JHA ($29) is written for your own task and the steps your crew gives us, with the rules picked from your answers. If your task is not in the library, or it is done in an unusual way, the Custom JHA fits better.

Where do the OSHA rules come from?

From the construction standards, 29 CFR Part 1926 (and 29 CFR 1910.178(l) and 1910.134 where Part 1926 points to them). Each rule is printed with its section number and a plain-words line, and every one is checked word for word against our saved copy of the regulation text. A control that no rule requires is written as a plain good-practice step, never as an OSHA requirement.

Can I edit them?

Yes. Every JHA comes as an editable Word file and a PDF. Add your company name, cross out steps that do not apply, and add your own steps, hazards and controls.

Do they work in every state?

They follow the federal OSHA construction rules. If you work in a State Plan state, such as California, Washington or Michigan, your state's rules can differ or go further, so check them as well.

Is this a subscription?

No. One payment, and the files are yours to keep and print. If the library is not right for you, email us within 14 days for a full refund.

A JHA ready for the next task, before the crew arrives

Get the library, $29